How to Install a Ghost Immobiliser
A ghost immobiliser guards your vehicle from key cloning and hacking. It works by stopping the engine from running until a PIN code is entered. This could be as long as 20 characters.
This additional layer of security isn't visible to thieves who may not be aware of it. Certain systems come with an app that allows the owner to disable their immobiliser in the event of forgetting their PIN or use the service/valet mode.
Connecting to the vehicle's CAN bus
The Ghost 2 Immobiliser is a cutting-edge security system, can be integrated directly into the ECU of your vehicle. It is a subtle protection against thieves. It is extremely efficient and user-friendly, making it a valuable component of your vehicle's security arsenal. But, as with ghost vehicle immobiliser -theft device, it's not impervious to failure and requires regular maintenance to ensure proper operation. This guide will help you make the most of your Ghost 2 immobiliser.
CAN (Controller Area Network), a robust serial networking that allows microcontrollers to communicate with each other over small distances. Central control units is not required. It is designed to allow multiplexing of electrical wiring inside vehicles to reduce copper usage and offers a range of advantages, including low cost and ease of use.
The CAN protocol is utilized in a majority of modern automobiles to connect with the engine management system, transmission controller, steering control module and air conditioning controls and many more. It also relays information from sensors, such as speed sensors and other inputs, to control the car's various features. The CAN bus is used to monitor these different components, and can prevent the car from starting if they are in a dangerous state.
Although the CAN bus can be utilized for a variety of reasons, it's essential to understand how it works and how it's secured. Using CAN bus can be a great way to enhance the features of your vehicle, but it's essential to safeguard it from threats such as hackers and other. The best method to achieve this is to install a firewall and monitoring your CAN bus using software.
Ghost2's discreet control unit is hidden away inside the car's wiring harness or dashboard, eliminating the possibility of a criminal physically altering it. It is impossible to reset a PIN or an emergency code without having access to the car.
If you have to give your car away to a valet parking service, maintenance, or any other reason, you can activate the Transport Mode. This feature will disable the Ghost immobiliser's keyfob and ignition functions, and will only reactivate when the vehicle is speeding at 31 mph for 15 minutes.
How do you create a PIN code
The Ghost immobiliser protects your car from thieves. The innovative technology uses the PIN to disable the vehicle's engine and prevent it starting without the correct code, or a valid fob or mobile. The system's sleek design makes it virtually invisible and provides unparalleled protection against theft. The system is TASSA certified and could save you substantial sums on your car insurance.
During installation, Ghost enters a "learning mode" to record the sequence of buttons that are pressed to create unique pin codes. The installer will guide you through activating the system after the pin code is created. Once activated, the Ghost system shuts down the vehicle's start motor unless you enter a valid pin or switch the vehicle into transport mode. This makes it very difficult for thieves to duplicate or hack your vehicle's starter system.
Installing a Ghost immobiliser is simple however it is essential to follow the precise instructions in the user guide to ensure proper operation. Multimeters and basic hand tools are a good way to check electrical values. Insulation tape as well as heat shrink tubing and cable ties can be used to shield exposed wiring. Also, be sure to test the system frequently to spot any issues or potential mistakes.
Once the installation has been completed, it is important to conduct a final test of the system before turning on the ignition in your vehicle. The Ghost immobiliser will re-arm itself after 3 to 30 seconds, depending on your vehicle model. The system is also equipped with a Service/Valet Mode that lets you temporarily disable the system for servicing or valet parking.
The immobiliser should be hidden in an inconspicuous location under the dashboard or steering wheel. It is recommended to use a small bit of paint or duct tape to mark the CAN H and CAN L wires so that you can easily find them when you are testing. Additionally the CAN H and L wires must be connected to a power source that has constant 12V. It is also essential to check the connections again after testing, since misidentifying these wires could cause the system to fail.
Invoking the system
A ghost immobiliser blocks your car from starting until you press certain buttons on the vehicle, typically on the steering wheel or the door panel, or the central console. The sequence is decided by the user and can be changed at any time. Once the system is activated it is not able to be disabled by thieves and is a great option for anyone who wishes to secure their vehicle from theft.
The system is designed to be undetectable, meaning it isn't detected by modern diagnostics or code-grabbing technology. It also does not send out radio frequencies, which makes it even difficult for thieves to find the device.
If the device is detected, it will prevent the engine from running and sound an alarm that is loud enough to deter thieves. The device can be used to track a car's location, which will aid in the search for the vehicle in case it has been stolen.
If you're interested in a ghost-immobiliser get in touch with the experts at Car Specalist Customs to get a quote and discuss your options. We are qualified to install ghost immobilisers in your vehicle. We will make sure that it is concealed in an area that is hard to reach. We can also provide other security measures like a wheel lock and kill switch to protect your vehicle from thieves.
Disarming the System
It is essential to know how to deactivate a Ghost immobiliser if it is fitted to your car. This will help you in the event that you lock your keys inside the car or when your battery fails. The system has a unique PIN code that only you know. It will not start the car without this code. Pressing a combination buttons on the steering wheel or on the dashboard is the easiest method to enter your code. This is a far simpler method than using the key fob, and it also keeps anyone from copying your remote.
Contrary to other aftermarket immobilisers which require cutting wires to install, Ghost2 is non-invasive and is compatible with your vehicle's bus network to operate. Its most distinctive feature is that it bypasses the engine without affecting normal vehicle functions. This makes it difficult for thieves to use signal boosters or duplicate keys to car keys. Furthermore, it doesn't emit radio frequencies, so thieves won't be able to detect it.
The Ghost system also features an option called Transport Mode that allows you to temporarily disable the security system in circumstances like transportation or servicing. This is a great option when you have to lend your vehicle to someone without sharing the PIN number or when you wish to secure your vehicle while driving it. To activate the Transport Mode, press the service button five times within 2 seconds. The Ghost system will confirm activation with 5 indication signals.
When you're done, remember to save the emergency code in a safe place outside of your vehicle. If you ever get locked out of your car you can contact the company or technician who installed the system and they'll give you the code. If you're unable to reach them, then you can contact an authorized dealer. However, this might involve verification procedures, and you may be charged for additional fees.
Apart from the ease of this system, you can also count on it to guard your vehicle from theft and help reduce the cost of insurance. Insurance companies often offer reduced monthly premiums, or even financial incentives for installing this anti-theft technology.